Bentley Continental Key Fob Troubleshooting Tips
The Bentley Continental is an incredibly impressive car to drive. The center stack is adorned with brushed metal, and the interior is adorned in beautiful wood and leather. Its mighty W12 engine generates 552 break horsepower.
The Continental key fob features rubber seals that stop water from destroying the electronic chip. If it is submerged in rain or clean tap water, it will be fine. However long exposure to saltwater can harm it.
Keyless entry system
The Bentley Continental comes with a keyless entry system, which allows you to lock and unlock your vehicle using the remote control. This is convenient, and can cut down on time. However, there are several reasons for your key fob to stop working. A few of them are dead batteries, water damage and receiver module issues. In certain cases, a malfunctioning internal chip could be the reason behind the issue.
The key fob is covered with rubber to keep water from entering the electronic chips. However the key fob may still be soaked if exposed to salt water or soapy water. This could damage your chip. It is important to allow the key fob to dry completely before replacing the battery. If the keyfob does not work after cleaning and drying it, then it is likely faulty and requires replacement.
The clips made of metal on the battery of your Continental keyfob hold it in place, and complete the circuit. Contact problems can occur if the clips are corroded or loose. Examine the battery contacts to ensure they are clean. Also, ensure that the battery is firmly installed. If you have an extra Continental key, try the key to see if it works. If the key is defective, you can reprogram it by using an OBDII scan.
Battery
The key fob is equipped with an insignificant battery of the size of a coin. The remote will not work when the battery for the coin is dead. This is easy to diagnose and can be replaced in a few minutes. The battery may be damaged by water, which will require a replacement. There are several reasons why the key fob may not function, including worn buttons, damaged battery contacts, signal interference or the receiver module is dead. It is possible to reset the system by disconnecting the 12 Volt batteries for a few minutes. This will allow the system to reset itself. Remove the negative cable first and then reconnect the positive cable.
The battery in the Bentley Continental key fob will last for four years depending on how often you use it. The battery is held in place by metal clips. The clips must be secure but if not then the remote won't perform as it should.
If the Continental keyfob is exposed to clean water from the tap, it should be dried and cleaned using an absorbent paper towel prior to reinstalling the battery. If the chip is exposed to salty or soapy water, it may be fried. In such cases you'll need to purchase a new key fob.
Water damage
David believes there are any major mechanical problems on this Continental. There is a little surface corrosion that has occurred when the wheels were exposed to road grit. The boot is spacious and practical with the factory warning triangle securing to the floor. There's also a space-saver spare wheel and the basic Bentley tools under the false floor.
The chip of the key fob is protected by rubber seals which will keep it working even if it's wet. The chip could be damaged through prolonged exposure to water. It is advisable to remove the key fob from your pocket prior to going paddling, kayaking, or rafting.
If your key fob was submerged in ocean or soapy water, you may try to save it. Make use of electronic cleaners or isopropyl ethanol to clean the chip. If the key fob doesn't function after cleaning and drying it you might need to replace it. If you're looking for a Bentley Continental Key Fob, ensure it is water-resistant and factory-paired to your vehicle.
Fault diagnosis
The Bentley Continental keyfob permits you to lock or unlock your car with just one click. It is easy to use and gives you security and safety when driving. However there are several things that can be wrong with your key fob. The most frequent reasons include a dead coin battery or water damage, signal interference or a damaged internal chip. There are some troubleshooting methods that you can apply to determine the cause of an electronic key fob not functioning.
The battery is the first thing to check. Verify that the battery has been correctly inserted and that all metal clips are in the proper position. If the clips are not tight the battery won't have a proper connection and will not function effectively. Additionally, the retaining clips must be free of corrosion.
A car battery that is weak is another reason that causes the key fob to fail to function. The 12 volt Continental battery must be in good health to communicate with your remote keyless entry system and the rest of the electronics onboard. Check the fuses and if needed, recharge your battery.
The Bentley Continental keyfob sends a message to the receiver module that is located inside the ignition barrel. If the signal isn't received, the engine won't start and an alarm will sound. If bently car key fob doesn't work, you should consult a professional.